Broken water pipe

Well a handmade piece of lamp work is boro glass, and you may take the pieces into any glass shop and ask them to heat it and fix it.

Stop smoking weed and get a real job.

Attached: 1512360843206.gif (400x300, 2M)

Get a new one you broke rerard

Don't be a cuck.

Have fun inhaling glue fumes you fucking idiot.

>non-argument

My man, you are really deep in the shit, aren't you? Save cumming inside of your girlfriend's cunt while you're level 10 stoned AFTER you've sorted out the fucking train wreck that is your life.

If you're freaking out over a broken water pipe and too cheap to simply buy a replacement, then you have some problems, man.

Study up, get a better job. If you had the extra money coming in from a decent gig you would have just shrugged your shoulders at the whole thing and proceeded to head over to your local headshop to procure some new glass.

It doesn’t get hot and is water based (That’s why it stays clear and doesn’t yellow).

>smoke isnt hot
Retard confirmed

Only solution outside huffing glue or buying a new one

>broke our water pipe!!
>broke our water pipe!!
broke our water pipe!!

Yup definitely retarded

How much glue do you think a clean break in glass can actually hold?

Hint, a new car would be more of a health hazard offgassing than him smoking from a bong with the end farthest from heat ever would.

Relax dude I'm not the OP. I just think all of the anti-weed nonsense is hilarious.

You do realize there are plastic bongs, right?

Alright man enjoy huffing glue. Im gonna not do that because I enjoy not being a broke junkie retard. Have fun!

Youre an idiot for a few reasons

You don’t even understand what YV glue is...

If you have white fillings, they are made from LOCA... so you are “ingesting” them 24/7...

>glue

Pure water can be a glue...

>heat
>mouth
>not retarded
Pick two and only two

The glass would be under colder conditions than your mouth.

Are you really this stupid?

This is retarded, it's not like you're putting the bowl piece back together with epoxy or something. Bong stems/chambers just don't get that hot, as long as it's not the bowl glue is fine, it just needs to be air and water tight

just buy a new one, there really arent any adhesives that i would be comfortable with using
only real option to fix that one is if you know someone that blows glass

And this isn’t kindergarten paste, it comes in a syringe, the amount that would be used is is something small because the clean break wouldn’t allow for much to be used. A drop would be too much. It’s water based, but once set with UV light it turns to plastic. It doesn’t smell and would be as invisible as a repair as possible.

Lol you should see what they use on water pipes lol.

> someone that blows glass
You can try /diy/. Or /b/ if glass blowing is a fetish.

Sorry, OP, speaking from experience -- you're better off just getting a new one. Even if it's a smaller chip, there's always a risk of inhaling chipped glass or it just shattering/getting worse. I've glued stuff together back before and no matter how careful or thorough I was it just broke again within a week.

Get you some papers or a cheap little glass pipe and put up with it until you can get a new bong.

Sorry to hear that, OP. Sounds like you need a new girlfriend. Pack all her shit in a box and leave it out the door. When she comes home, open the door and hand her the broken bong. Let her stand there in confusion before the weight of her mistakes come crashing down.

In all seriousness, buy a new bong m8

Problem is we don’t know if it’s borosilicate glass.

I actually do museum quality repairs on glass, if you didn’t use UV cured adhesive, well that says it all.

glass blowing is the process of making things out of glass, and it requires specialized equipment and tools

And if this piece is borosilicate glass, a simple two gas torch could be used to heat the top to a red glow causing the pieces to fuse... its not that big of a deal.

Better yet.. Get her to buy it. She broke it